Chip 1997 March/CHIP Mart 1997.iso/SurfCam/SURFCAM.Z/FAN10S54.M3

Text File | 1996-04-01 | 5KB | 180 lines

name Fanuc 10M Sub Programs 54-59

^ 00
% 00
/ 00
O 4
N >4
G >2
g >2 G
X ->3.>4
Y ->3.>4
Z ->3.>4
A ->3.>4
I ->3.>4
J ->3.>4
K ->3.>4
Q ->3.>4
R ->3.>4
P 4
F >3.1
H >2
D >2
T >2
M >2
L >2
S >4
c 00

ModalLetters X Y Z F R                # List of letters that are modal

ModalGs 0 1 2 3 73 74 76 80 81 82 83 84 85  # List of g codes that are modal

Sequence#s N 0 1 1                    # Char, freq, incr & start
First#? N                             # Y or N  'Output 1st sequence no.
Last#? N                              # Y or N  'Output last sequence no.

HCode X                               # X or X U  'Horizontal char.
VCode Y                               # Y or Y V  'Vertical char.
Dcode Z                               # Depth char.
FeedCode F                            # Feed rate char.

Comment ( )                           # Begin End comment char.

Spindle 3 4 5                         # Cw, ccw & stop m codes
Coolant 8 9 7                         # On, Off & Mist m codes
DComp 41 42 40                        # Left, Right & Cancel m codes
LComp 43 49                           # On & Off codes

Feed G1                             # Linear move
Rapid G0                            # Rapid positioning word
Cw G2                               # Circular move clockwise
Ccw G3                              # Circular move counter clockwise

Inc/Abs G 91 90                       # Inc & Abs char. & values

CtrCode I J                           # I J or R or I J K L
Helical? Y

Spaces? Y                             # Y or N  'Spaces between words

Incremental? N                        # Y or N  'Inc or abs output
CtrIncremental? Y                     # Y or N  'Inc or abs I & J
ByQuadrants? N                        # Y or N  'Break arcs at quadrants
Subs1st? N                            # Y or N 'Orders main & sub programs

UppercaseComments? Y                  # Y or N 'Require uppercase comments


Drill                                 # Drilling canned/manual cycle
G81 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Peck                                  # Pecking canned/manual cycle
G83 X[H] Y[V] Z[D] Q[VBite] R[Vclear] F[FRate]
end cancel

Tap                                   # Tapping canned/manual cycle
G84 X[H] Y[V] Z[D] R[Vclear] F[FRate] Q[VBite]
end cancel

LTap                                  # Left handed tapping cycle
G74 X[H] Y[V] Z[D] R[Vclear] F[Frate] Q[VBite]
end cancel

Ream                                  # Reaming canned/manual cycle
G85 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Bore                                  # Boring canned/manual cycle
G86 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Back                                  # Back boring canned/manual cycle
G87 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Cancel                                # Cancel a canned/manual cycle
G80
end

Drill                                 # Drilling canned/manual cycle
G81 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Peck                                  # Pecking canned/manual cycle
G83 X[H] Y[V] Z[D] Q[VBite] R[Vclear] F[FRate]
end cancel

Tap                                   # Tapping canned/manual cycle
G84 X[H] Y[V] Z[D] R[Vclear] F[FRate] Q[VBite]
end cancel

LTap                                  # Left handed tapping cycle
G74 X[H] Y[V] Z[D] R[Vclear] F[Frate] Q[VBite]
end cancel

Ream                                  # Reaming canned/manual cycle
G85 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Bore                                  # Boring canned/manual cycle
G86 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Back                                  # Back boring canned/manual cycle
G87 X[H] Y[V] Z[D] R[Vclear] F[FRate]
end cancel

Cancel                                # Cancel a canned/manual cycle
G80
end

StartCode                             # Start of the program
%0
End

1stToolChange                         # First tool change
O[Program#]
G0 G40 G80 G90
T[Tool] M6
M8
G90 X[H] Y[V]
G0 G43 Z[D] S[Speed] M[Direct] H[Lcomp]
End

Infeed                                # Enable cutter comp
G[Side] X[H] Y[V] D[DComp] F[FRate]
end

Outfeed                               # Disable cutter comp
G1 G40 X[H] Y[V]
end

ToolChange                            # Secondary tool changes
T[Tool] M6
M8
G90 X[H] Y[V]
G0 G43 Z[D] S[Speed] M[Direct] H[Lcomp]
End

Between                               # Between the main and sub programs
M9
g91 G80 G30 Y0 Z0
G0 G40 G80 G90
M30
End

SubCall                               # Call a sub program
G[Work] X[H] Y[V] P[Sub] M98
End

SubStart                              # Start of the sub program
O[Sub]
End

SubEnd                                # End of the sub program
M99
End